Sauna Library - Aufguss
What Happens to Water on Sauna Stones?
Short answer: Aufguss water does not create heat. When water reaches sufficiently hot sauna stones, energy flows from the stones into the liquid. The water is heated, reaches conditions at which liquid can change phase, and is converted into water vapour. This phase transition requires a large amount of energy—the latent heat of vaporisation—which temporarily cools the wetted stone surfaces. The vapour then mixes with the hot cabin air and is transported by the heater plume, natural convection, ventilation and fanning. The resulting rise in water-vapour pressure changes heat exchange at the skin: sweat evaporates less readily, and some vapour can condense on the cooler body surface, releasing latent heat there. This is why an Aufguss can feel dramatically hotter even though pouring water onto the stones has not added energy to the sauna.
The defining physical event of an Aufguss lasts only seconds: liquid water meets a much hotter stone bed and disappears from view. Yet those few seconds initiate a chain of heat and mass-transfer processes that changes the entire thermal experience of the cabin.
Understanding that chain removes several persistent misconceptions. The water does not 'make the sauna hotter' by supplying heat. Steam is not simply a visible cloud that floats through the room. And the intense heat pulse felt by the bather cannot be explained by air temperature alone.
Aufguss is a controlled transfer of energy and water—not the creation of additional heat.
Step 1: liquid water reaches the hot stone bed
Aufguss begins when liquid water is distributed over stones that have stored thermal energy from the heater. The water spreads over exposed surfaces, runs between stones and, depending on stone shape, temperature and flow rate, may penetrate into deeper parts of the stone bed.
Heat immediately flows from the hotter solid into the cooler liquid. The direction is determined by the temperature difference: energy moves spontaneously from the hot stones toward the cooler water.
The stone surface therefore begins to cool from the moment it is wetted.
Step 2: the water must first be heated
Before liquid water can be vaporised, energy must raise its temperature. This is sensible heating and can be approximated by Q = m × c × ΔT.
For one kilogram of water heated from 20 °C to 100 °C, using a specific heat capacity of about 4.18 kJ/(kg·K), the sensible heat requirement is approximately 334 kJ.
For 100 g of water, the corresponding value is about 33 kJ. This is only the first part of the energy demand.
Step 3: the phase transition requires much more energy
At atmospheric pressure, converting liquid water at 100 °C into water vapour requires approximately 2.26 MJ/kg of latent heat. No additional temperature rise is required for this phase change at the boiling point; the energy changes the molecular state.
Starting with water at about 20 °C, heating and fully vaporising one kilogram therefore requires roughly 2.6 MJ. For 100 g, the order of magnitude is approximately 0.26 MJ.
This large latent-energy requirement is why the thermal state of the stone bed matters so much.
Most of the energy needed for an Aufguss goes into the phase transition—not into warming the liquid water.
Where does that energy come from?
Primarily from the hot stone surfaces and the thermal mass behind them. The active heater simultaneously continues to supply energy according to its control state.
The water therefore removes energy from the stone bed during evaporation. The local surface temperature falls, after which heat conducts from hotter regions within the stones and from the heater back toward the cooled surfaces.
Aufguss is thus a transient discharge and recovery of the heater–stone thermal reservoir.
Does pouring water increase the total energy in the sauna?
No. The water normally enters much cooler than the stones and must absorb energy from the sauna system.
The striking increase in perceived heat after Aufguss is therefore not evidence that the water has added heat. It has changed the form, location and transfer pathways of energy already present.
This distinction is fundamental to the physics of Aufguss.
The sauna can feel hotter while the stones are actually losing heat.
Evaporation or boiling?
The everyday word 'evaporation' is useful but can hide two related processes. Evaporation can occur from a liquid surface below the boiling temperature, whereas boiling involves vapour formation when the liquid's vapour pressure reaches the surrounding pressure.
On very hot sauna stones, droplets can undergo vigorous boiling and rapid vaporisation. Some water may also spread, penetrate between stones or evaporate from wetted surfaces as its temperature changes.
The relevant outcome for the cabin is the same: liquid water becomes gaseous water vapour and joins the sauna air.
Does water have to reach exactly 100 °C?
No. Water can evaporate below 100 °C; wet clothing dries at room temperature for the same reason. One hundred degrees Celsius is the normal boiling point of pure water at approximately standard atmospheric pressure.
On hot stones, however, heat transfer is so intense that water can be heated and vaporised extremely rapidly.
Using 100 °C in an energy example is therefore a convenient reference for the boiling pathway, not a claim that every molecule follows one identical microscopic history.
What happens to a droplet on a very hot surface?
Droplet behaviour depends strongly on surface temperature, roughness, wetting, porosity and impact conditions. At sufficiently high surface temperatures, vapour generated beneath a droplet can partially insulate it from the solid—the phenomenon associated with the Leidenfrost effect.
Sauna stones are irregular, rough and often porous rather than smooth laboratory plates. Water can split, penetrate crevices and contact surfaces at many different temperatures, so a simple Leidenfrost picture should not be applied to the entire stone bed.
Research on natural stone shows that impact, spreading, absorption and evaporation depend strongly on the stone's pore structure and wetting behaviour [1].
Why stone surface area matters
A bed of many irregular stones provides far more accessible surface than a single solid block of the same overall size. Water can divide into smaller streams and films and encounter hot surfaces at several depths.
Increasing the effective liquid–solid contact area increases the opportunity for rapid heat transfer.
This is one reason correctly sized and arranged sauna stones are important to Aufguss performance.
What happens if the water penetrates deeper?
Water that passes between the upper stones can encounter hot surfaces deeper in the heater. This spreads the thermal load over a larger part of the stone mass.
Rounded upper stones may encourage deeper water travel in heater designs that permit them, whereas angular stones provide large fracture surfaces and irregular flow paths.
The outcome depends on heater architecture and stone arrangement; deeper penetration is not automatically better in every heater.
What if too much water is applied at once?
The stone bed has a finite instantaneous capacity to transfer heat. If water arrives faster than sufficiently hot surfaces can vaporise it, some liquid may travel through the bed before complete evaporation.
This can cool the stones strongly and may allow water to reach parts of the heater not intended for excessive liquid exposure.
The practical limit is therefore not merely 'how much water fits on the stones', but how much water the thermal system can vaporise safely and controllably.
Why does the stone bed recover?
After the wetting event, temperature gradients exist inside the stones: the wetted surface is cooler than deeper material. Thermal conduction moves energy toward the cooled region.
At the same time, the heater elements or combustion system continue restoring energy to the stone bed.
Recovery time depends on heater power, stone mass, stone conductivity, water quantity and how soon the next Aufguss occurs.
What exactly enters the cabin?
The phase change produces water vapour: individual H₂O molecules in the gas phase mixed with the cabin air.
Pure water vapour is invisible. A visible white cloud consists of microscopic liquid droplets formed when vapour condenses in cooler air.
The familiar phrase 'steam cloud' is therefore visually understandable but physically imprecise.
Water vapour is invisible. What you can see is condensed water.
Is water vapour lighter than air?
An isolated water molecule has a lower molar mass than the average molecules of dry air, but this fact alone does not explain Aufguss circulation.
The vapour leaves a very hot stone bed together with strongly heated air. The resulting plume rises primarily because it is hot and buoyant, while the cabin's existing convection and ventilation determine its subsequent path.
Treating steam as a separate substance that simply 'rises because it is lighter' is therefore an oversimplification.
What is the heater plume?
Air heated in and around the stove expands, becomes less dense and rises. This creates a strong convective plume above the heater.
When Aufguss water vaporises, the added water vapour is entrained into this moving hot air and transported rapidly toward the upper cabin.
The plume is therefore the first major transport mechanism carrying the Aufguss away from the stones.
Why does the upper bench feel the Aufguss first?
The upper cabin is already the hottest region because of thermal stratification. The buoyant heater plume carries the newly humidified air upward into this zone.
Bathers on the upper bench are therefore exposed early to the combination of high air temperature and increased water-vapour pressure.
This is one reason the same Aufguss can feel much stronger on the upper bench than on the lower one.
How does the vapour spread through the cabin?
After the initial upward transport, water vapour is redistributed by natural convection, ventilation, movement of people and deliberate fanning.
Because water vapour is a gas component of the air mixture, it diffuses and is advected with the moving cabin air rather than remaining as a permanent separate layer.
The final distribution therefore depends on room geometry, heater position, ventilation and air movement.
What does ventilation do to the vapour?
Ventilation continuously removes part of the humid cabin air and replaces it with supply air. It therefore sets a time scale for how long the added moisture remains in the sauna.
A high exhaust close to the upper vapour-rich zone can remove part of the Aufguss rapidly. A lower exhaust can encourage the mixed air to travel through more of the occupied zone before leaving.
Ventilation must maintain air quality without unnecessarily short-circuiting the Aufguss.
What does fanning actually do?
Fanning does not produce additional water vapour and does not generate heat. It moves the already hot, humid air through the cabin and across the bather's skin.
This disrupts the relatively insulating boundary layer around the body and increases convective and mass transfer.
Fanning is therefore a transport-control technique: it determines where and how quickly the altered Aufguss atmosphere reaches people.
Water changes the cabin atmosphere. Fanning changes where that atmosphere goes.
What happens to absolute humidity?
Adding water vapour increases the mass of water contained in a given volume or mass of sauna air. Absolute humidity, humidity ratio and water-vapour pressure therefore rise after Aufguss.
These quantities are physically more informative than relative humidity alone when describing the amount of water vapour added.
The amount of vapour present then falls again through ventilation, condensation and exchange with surfaces.
What happens to relative humidity?
Relative humidity is the ratio between the actual water-vapour pressure and the saturation vapour pressure at the same temperature. Because saturation vapour pressure rises steeply with temperature, relative humidity is highly temperature-dependent.
Adding the same mass of water vapour can therefore produce very different RH values at different temperatures.
A sauna can have a comparatively low relative humidity while still containing a substantial absolute amount of water vapour.
Why does Aufguss feel hotter?
The body in a hot sauna relies heavily on sweat evaporation for heat loss. Leppäluoto described evaporative heat transfer as the only effective avenue of heat dissipation under classic Finnish sauna conditions [2].
When water-vapour pressure rises, the gradient driving evaporation from the wet skin decreases. Sweat therefore evaporates less effectively.
At the same time, hot humid air can transfer more heat to the skin, and water vapour can condense on the cooler body surface.
Aufguss makes heat harder to lose and easier to transfer to the skin.
Can water vapour really condense on the skin?
Yes. The skin is much cooler than the hottest sauna air, particularly before it has fully warmed. If local vapour conditions exceed saturation at the skin-surface temperature, some water vapour can condense.
A stable-isotope sauna experiment directly demonstrated that a substantial fraction of water dripping from bathers after löyly came from condensation of the thrown water rather than from sweat [3].
Depending on the experimental series and calculation method, mean condensation contributions were approximately 30–54% of the dripping water [3].
Why condensation matters thermally
Vaporisation on the stones absorbs latent heat. Condensation is the reverse phase transition and releases latent heat.
If water vapour condenses on the skin, energy associated with that phase change is delivered at the body surface. This contributes to the characteristic heat pulse of Aufguss.
The same energy principle therefore links the cooling of the stones with the heating sensation at the skin.
Latent heat is absorbed at the stones and can be released again when vapour condenses on cooler surfaces.
Is all the vapour condensed on the body?
No. Much of it remains mixed with the cabin air and is eventually removed by ventilation or condenses elsewhere as conditions change.
The isotope experiment demonstrates that skin condensation can be substantial, not that all Aufguss water reaches the bather.
Walls, ceiling, benches, ventilation and remaining cabin air all participate in the water balance.
Why can the walls become wet?
If a surface is cool enough that the local air becomes saturated at that surface, water vapour can condense there.
During repeated Aufgüsse, cooler construction elements can therefore accumulate moisture even though the bulk sauna air remains far from 100% relative humidity.
This is one reason drying ventilation after operation matters for sauna construction.
Does the air temperature rise during Aufguss?
It does not need to rise for the bather to feel a strong heat pulse. Vaporising the water actually removes energy from the stones, and local air-temperature changes depend on the entire transient heat balance.
The decisive physiological change can occur through increased water-vapour pressure and altered heat transfer rather than through a large increase in dry-bulb temperature.
Recent human research confirms that temperature and relative humidity independently influence acute thermoregulatory and cardiovascular responses during Finnish sauna bathing [4].
What did the 2026 study show?
In 50 healthy recreationally active adults completing four 10-minute Finnish sauna exposures, both sauna temperature and relative humidity were independently associated with heart-rate and core-temperature responses [4].
The study did not isolate a single standardised Aufguss dose, because participants were allowed to throw water on the stones according to preference. It therefore should not be used to calculate a precise physiological effect per gram of water.
It nevertheless reinforces the central principle: humidity is an independent component of sauna heat load.
Why water quantity matters
More water means more mass that must be heated and vaporised, and—if vaporisation occurs—more water vapour added to the cabin.
The relationship with perceived intensity is not perfectly linear because stone temperature, ventilation, timing, cabin volume, fanning and condensation all modify the result.
This is why professional Aufguss should control water quantity relative to cabin volume rather than treating the ladle as a standard dose.
The Academy's water-dose framework
For health-oriented Aufguss, the International Sauna Academy uses approximately 15–30 g of water per cubic metre of cabin volume as a controlled working range, with 30 g/m³ as the upper orientation for the health-oriented procedure.
This is an Academy practice standard, not a universal physiological threshold or a value derived from one clinical trial.
Expressing water relative to cabin volume is nevertheless more meaningful than specifying only 'one, two or three ladles' because ladle size and room volume vary.
An example: 20 m³ cabin
At 15 g/m³, a 20 m³ cabin receives 300 g of Aufguss water. At 30 g/m³, it receives 600 g.
Starting from approximately 20 °C, complete heating and vaporisation of 300 g requires roughly 0.78 MJ; 600 g requires roughly 1.56 MJ.
These are thermodynamic order-of-magnitude calculations. Real heat transfer is distributed across stones, heater, air and surfaces, and not every gram necessarily follows an identical path.
Why a second Aufguss can behave differently
After the first water application, parts of the stone bed have cooled. The heater begins restoring energy, but recovery is not instantaneous.
A second equal water dose delivered shortly afterwards may therefore encounter different stone-surface temperatures and produce a different evaporation pattern.
Professional dosing must consider thermal recovery, not merely repeat the same volume mechanically.
Why pouring technique matters
A concentrated stream can overload a small region of the stone bed, whereas broader distribution exposes more hot surface.
The speed of application also changes the instantaneous heat-transfer demand. The same total mass delivered over a longer interval may behave differently from a rapid dump.
Water quantity, distribution and timing are therefore separate variables.
Does hotter water reduce the energy demand?
Yes, slightly. Warm water requires less sensible heating before phase change than cold water.
But the sensible-heating term is much smaller than the latent heat of vaporisation. Heating one kilogram from 20 to 100 °C requires about 0.33 MJ, while vaporising it at 100 °C requires about 2.26 MJ.
The dominant energy demand is therefore the phase transition itself.
Would boiling water make a stronger Aufguss?
Not in proportion to its starting temperature. Water already near boiling saves the sensible-heating portion, but the large latent-energy requirement remains.
Using very hot water also creates handling and scalding hazards without providing a corresponding thermodynamic advantage for ordinary professional practice.
The quality of Aufguss depends far more on stone condition, dose, distribution and cabin-air management.
Does every gram become vapour immediately?
Not necessarily. Some water may remain temporarily within the stone bed, penetrate porous surfaces, reach cooler regions or drain before complete vaporisation.
Research on porous natural stones shows that droplet spreading, absorption, moisture redistribution and evaporation depend strongly on lithology and pore structure [1,5]. These studies are not sauna-heater experiments, but they illustrate why real stone–water interaction is more complex than an ideal hot plate.
A professional model should therefore distinguish the intended water dose from the mass that is instantaneously vaporised.
What happens after the heat pulse?
Ventilation progressively removes humid air, surfaces exchange moisture with the cabin, and the stone bed reheats.
Sweat evaporation becomes easier again as water-vapour pressure falls. The cabin therefore moves back toward its pre-Aufguss thermal and moisture state.
The rate of recovery depends on ventilation, heater output, stone mass, room surfaces and the amount of water used.
Why repeated Aufgüsse can accumulate
If another Aufguss occurs before humidity and stone temperature have returned toward baseline, the new event begins from a different initial condition.
Water-vapour content may already be elevated while the stones may still be partially cooled. The subjective and physiological response can therefore differ even when the same amount of water is used.
Repeated Aufguss is a sequence of coupled transient events, not a set of identical independent doses.
What happens to the bather's heat balance?
Before Aufguss, the body receives heat by radiation and convection while trying to lose heat through sweat evaporation.
After water vapour is added, evaporative heat loss becomes less effective. If condensation occurs, latent heat can additionally be transferred to the skin.
The net balance therefore shifts toward greater heat storage unless exposure is reduced or the person leaves the cabin.
Why this matters for safety
A strong Aufguss can increase thermal strain rapidly without a dramatic change in the displayed air temperature.
Thermometers alone therefore cannot describe Aufguss intensity. Water dose, cabin volume, stone temperature, humidity, fanning, bench position and exposure time all matter.
The operator should control these variables rather than using subjective spectacle as a substitute for thermal-dose management.
A useful physical model
The sequence can be summarised as: liquid water → sensible heating → phase transition → water vapour → convective transport and mixing → reduced sweat evaporation and possible condensation → increased heat transfer to the bather.
At the same time, the stone bed follows the reverse energy sequence: stored thermal energy → water heating and vaporisation → local stone cooling → conductive and heater-driven recovery.
Water pathway: liquid → vapour → cabin → skin/surfaces/exhaust. Energy pathway: stones → water → vapour transfer → body and surroundings.
What is the most common misconception?
The most common misconception is that the Aufguss 'raises the sauna temperature' and that this explains the heat sensation.
In reality, the central change is moisture and heat-transfer dynamics. The stones lose energy to vaporise water, while the bather can simultaneously experience greater thermal load because evaporation from the skin is restricted and condensation can transfer latent heat.
The paradox disappears once energy and temperature are no longer treated as the same thing.
So, what happens to water on sauna stones?
It receives heat from the stone bed, warms, changes from liquid to vapour and becomes part of the cabin's gas mixture. The heater plume initially carries that vapour upward, after which convection, ventilation and fanning redistribute it.
The increased water-vapour pressure alters the bather's heat balance. Sweat evaporates less effectively, and some vapour may condense on the cooler skin and release latent heat.
Meanwhile, the stones have cooled and must recover before they can reproduce the same evaporation conditions.
Conclusion
The physics of Aufguss is a sequence of coupled heat and mass transfers. Water is heated, vaporised, transported, mixed and eventually removed or condensed. None of these steps creates energy.
What makes Aufguss powerful is the conversion and redistribution of energy already stored in the sauna system. Vaporisation consumes latent heat at the stones; increased humidity suppresses evaporative cooling at the skin; condensation can return latent heat directly to the body.
This is why a relatively small quantity of water can transform the thermal experience of an otherwise stable sauna within seconds.
Understanding that process provides the physical foundation for professional decisions about water quantity, stone temperature, fanning, ventilation and safe thermal dose.
References
1. Lee JB, Radu AI, Vontobel P, Derome D, Carmeliet J. Absorption of impinging water droplet in porous stones. Journal of Colloid and Interface Science. 2016;471:59–70. doi:10.1016/j.jcis.2016.03.002. PMID: 26975034.
2. Leppäluoto J. Human thermoregulation in sauna. Annals of Clinical Research. 1988;20(4):240–243. PMID: 3218894.
3. Zech M, Bösel S, Tuthorn M, et al. Sauna, sweat and science—quantifying the proportion of condensation water versus sweat using a stable water isotope tracer experiment. Isotopes in Environmental and Health Studies. 2015;51(3):439–447. doi:10.1080/10256016.2015.1057136. PMID: 26110629.
4. Temperature and humidity independently influence thermoregulatory responses during Finnish sauna bathing. Temperature. 2026. PMID: 42694940.
5. Slavík M, Bruthans J, Schweigstillová J. Evaporation rate from surfaces of various granular rocks: comparison of measured and calculated values. Science of the Total Environment. 2023;856(Pt 2):159114. doi:10.1016/j.scitotenv.2022.159114. PMID: 36181825.
6. Helamaa E, Aikäs E. The secret of good löyly. Annals of Clinical Research. 1988;20(4):224–229. PMID: 3218892.
7. Havenith G, Bröde P, den Hartog E, et al. Evaporative cooling: effective latent heat of evaporation in relation to evaporation distance from the skin. Journal of Applied Physiology. 2013;114(6):778–785. doi:10.1152/japplphysiol.01271.2012. PMID: 23329814.
8. Incropera FP, DeWitt DP, Bergman TL, Lavine AS. Fundamentals of Heat and Mass Transfer. Principles of sensible heating, phase change, convection, diffusion and transient heat transfer.
9. Gröning K. The Art and Science of Sauna Aufguss. International Sauna Academy, 2026. Sections on water quantity, evaporation, vapour pressure, condensation, fanning and thermal dose.
Editorial note: Thermodynamic values are rounded engineering values at approximately atmospheric pressure. Real sauna-stone evaporation is transient and spatially heterogeneous; the calculations illustrate energy magnitudes rather than assuming that every gram of water follows an identical path.
